SSC JE Civil Syllabus PDF and Exam Pattern | Download Here
For a comprehensive understanding of the SSC JE Exam, we have compiled important information in this article. Candidates are urged to refer to the following table for crucial details about SSC JE Civil Syllabus:
SSC JE Civil Syllabus: A Comprehensive Guide
SSC JE Civil Syllabus PDF: To excel in the SSC JE Civil Exam, candidates must familiarize themselves with the extensive SSC JE Civil Syllabus. Given the vastness of the syllabus, every candidate must be well-acquainted with every topic covered in the SSC JE Exam. The SSC Junior Engineering (SSC JE) Civil Exam consists of two papers, namely Paper 1 and Paper 2. Aspiring candidates must have a thorough understanding of the SSC JE syllabus, encompassing all engineering branches, including Civil, Electrical, and Mechanical.
Overview of SSC JE Civil Syllabus PDF
For a comprehensive understanding of the SSC JE Exam, we have compiled important information in the table below.
Candidates are urged to refer to the following table for crucial details about SSC JE Civil Syllabus:
| Conducting Authority | Staff Selection Commission (SSC) |
| Post | Junior Engineer |
| Branch | Junior Engineer (Civil) |
| Job Category | Govt Job |
| Exam Mode | Online and Offline |
| SSC JE Syllabus | Available Now |
| Selection Process | Computer-Based Test (Paper I) and Descriptive Test(Paper II) |
| SSC Official Website | ssc.nic.in |
SSC JE Civil Syllabus Details
The questions in the Engineering subjects will be based on the level of a Diploma in Civil Engineering from a recognized Institute, Board, or University approved by the All India Board of Technical Education. Below are the detailed syllabus for both Paper-I and Paper II of the SSC JE exam.
| Papers | Type of Examination | Subjects | Mode of examination |
|---|---|---|---|
| Paper 1 | Objective Multiple Choice | (i) General Intelligence and Reasoning(ii) General Awareness (iii) Part-A General Engineering (Civil & Structural) | CBT (Online) |
| Paper 2 | Descriptive Test | Part-A General Engineering (Civil & Structural) | Pen and Paper Mode |
SSC JE Exam Pattern
SSC JE Examination will consist of two papers i.e. Paper-I and Paper-II. The Paper-I will be conducted online (Computer Based Examination). Paper-II Exam is a Descriptive Type Paper that is held offline (Written Examination). You need to check the exam pattern before going through the syllabus of SSC JE.
SSC JE Paper-I Exam Pattern
| Subject | Number of Questions | Maximum Marks |
|---|---|---|
| General Awareness | 50 | 50 |
| General Intelligence and Reasoning | 50 | 50 |
| Part A- General Engineering (civil & structural) or Part B- General Engineering (Electrical) or Part C- General Engineering (Mechanical) or | 100 | 100 |
Note: There will be a negative marking of 0.25 marks for each wrong answer in Paper-I.
IMPORTANT LINKS
| Download PDF File of SSC JE Civil Syllabus |
| SSC JE Civil Study Material | PDF Download CLICK HERE |
| SSC JE Civil Previous Year Papers/Model Test Papers | PDF CLICK HERE |
SSC JE Civil Syllabus for Paper-I
SSC JE Paper 1 is conducted in online mode and has three sections which are mentioned below:
(i) General Intelligence and Reasoning
(ii) General Awareness
(iii) General Engineering- Civil and Structural
1. SSC JE Syllabus for General Intelligence & Reasoning
SSC covers both verbal and non-verbal type questions in General Intelligence & Reasoning section. The test will also include questions designed to test the candidate’s abilities to deal with abstract ideas and symbols and their relationships, arithmetical computations and other analytical functions.
- Classification
- Analogy
- Coding-Decoding
- Paper Folding Method
- Matrix
- Word Formation
- Venn Diagram
- Direction and Distance
- Blood Relations
- Series
- Verbal reasoning
- Non-Verbal Reasoning
- Seating Arrangement
- Puzzles & Seating Arrangement
2. SSC JE Syllabus for General Awareness
Questions asked in this section will be aimed at testing the candidate’s general awareness of the environment around him/her and its application to society. Questions will also be designed to test knowledge of current events and of such matters of everyday observations and experience in their scientific aspect as may be expected of any educated person.
- Static General Knowledge
- Science
- Current Affairs
- Sports
- Books and Authors
- Important Schemes
- Portfolios
- People in the News
- History
- Culture
- Geography
- Economic
- Awards and Honors
3. SSC JE Syllabus for General Engineering (Civil and Structural)
- Building Materials
- Surveying
- Estimating
- Soil Mechanics
- Costing and Valuation
- Concrete Technology
- Irrigation Engineering
- Steel Design
- Theory of Structures
- Hydraulics
- RCC Design
- Environmental Engineering
- Transportation Engineering
SSC JE Syllabus for Paper II
SSC JE Paper-II Exam Pattern
Tier II is a written exam of 300 marks for a duration of 2 hours.
| Subject | Maximum Marks | Duration & Timings |
|---|---|---|
| Part A- General Engineering (Civil & Structural) | 300 | 2 Hours |
SSC JE Syllabus For Civil Engineering
| Building Materials | 1. Physical and chemical properties. 2. Classification, Standard Tests, Uses and Manufacture/Quarrying of Materials. |
| Estimating, Costing, and Valuation | 1, Estimate, a glossary of technical terms, analysis of rates, methods and unit of measurement, Items of work – earthwork, Brick work (Modular & Traditional bricks), RCC work, Shuttering, Timber work, Painting, Flooring, and Plastering. 2. Boundary wall, Brick building, Water Tank, Septic tank, Bar bending schedule, Centre line method, Mid-section formula, Trapezoidal formula, Simpson’s rule. 3. Cost estimate of Septic tank, flexible pavements, Tube well, isolates and combined footings, Steel Truss, Piles, and pile-caps. 4. Valuation – Value and cost, scrap value, salvage value, assessed value, sinking fund, depreciation and obsolescence, methods of Valuation. |
| Surveying | 1. Principles of surveying, measurement of distance, chain surveying. 2. Working on the prismatic compass, compass traversing, bearings, local attraction, plane table surveying. 3. The theodolite traversing, adjustment of theodolite, Leveling, Definition of terms used in leveling, contouring, curvature, and refraction corrections. 4. Temporary and permanent adjustments of dumpy level, methods of contouring. 5. Uses of a contour map, tachometric survey, curve settingEarthwork calculation, advanced surveying equipment. |
| Soil Mechanics | 1. Origin of soil, phase diagram, Definitions-void ratio, porosity, degree of saturation, water content, the specific gravity of soil grains, unit weights, density index, and interrelationship of different parameters, Grain size distribution curves, and their uses. 2. Index properties of soils, Atterberg’s limits, ISI soil classification, and plasticity chart. 3. Permeability of soil, coefficient of permeability, determination of coefficient of permeability, Unconfined and confined aquifers, effective stress, quicksand, consolidation of soils, Principles of consolidation, degree of consolidation, pre-consolidation pressure, normally consolidated soil, e-log p curve, computation of ultimate settlement. 4. Shear strength of soils, direct shear test, Vane shear test, Triaxial test. 5. Soil compaction, Laboratory compaction test, Maximum dry density and optimum moisture content, earth pressure theories, active and passive earth pressures, Bearing capacity of soils, plate load test, standard penetration test. |
| Hydraulics | 1. Fluid properties and hydrostatics, measurements of flow.Bernoulli’s theorem and its application.Flow-through pipes. 2. Flow in open channels, weirs, flumes, spillways, pumps, and turbines. |
| Irrigation Engineering | 1. Definition, necessity, benefits, 2II effects of irrigation, types, and methods of irrigation. 2. Hydrology – Measurement of rainfall, runoff coefficient, rain gauge. 3. Losses from precipitation – evaporation, infiltration, etc. 4. Water requirement of crops, duty, delta and base period, Kharif and Rabi Crops, Command area, Time factor, Crop ratio, Overlap allowance, Irrigation efficiencies. 5. Different types of canals, types of canal irrigation, loss of water in canals. 6. Canal lining – types and advantages. 7. Shallow and deep to wells, the yield from a well. 8. Weir and barrage, Failure of weirs and permeable foundation, Slit, and Scour, Kennedy’s theory of critical velocity. 9. Lacey’s theory of uniform flow. 10. Definition of flood, causes, and effects, methods of flood control, water logging, preventive measure. |
| Transportation Engineering | 1. Highway Engineering: cross-sectional elements, geometric design, types of pavements, pavement materials 2. Aggregates and bitumen, different tests, Design of flexible and rigid pavements. 3. Water Bound Macadam (WBM) and Wet Mix Macadam (WMM), Gravel Road, Bituminous construction, Rigid pavement joint, pavement maintenance, Highway drainage, Railway Engineering. 4. Components of the permanent way -Sleepers, ballast, fixtures and fastening, track geometry, points and crossings, track junction, stations, and yards. 5. Traffic Engineering – Different traffic survey, speed-flow-density, and their interrelationships, intersections, and interchanges, traffic signals, traffic operation, traffic signs and markings, road safety. |
| Environmental Engineering | 1. Quality of water, source of water supply, purification of water, distribution of water, need of sanitation, sewerage systems, circular sewer, oval sewer, sewer appurtenances, sewage treatments. 2. Surface water drainage. 3. Solid waste management – types, effects, engineered management system. 4. Air pollution – pollutants, causes, effects, control.Noise pollution – cause, health effects, control. |
SSC JE Syllabus For Structural Engineering
| Theory of Structures | 1. Elasticity constants, types of beams – determinate and indeterminate, bending moment and shear force diagrams of simply supported, cantilever, and overhanging beams. 2. Moment of area and moment of inertia for rectangular & circular sections, bending moment, and shear stress for tee, channel, and compound sections. 3. Chimneys, dams and retaining walls, eccentric loads, slope deflection of simply supported and cantilever beams, critical load and columns, Torsion of circular section. |
| Concrete Technology | 1. Properties, Advantages and uses of concrete, cement aggregates, the importance of water quality, water-cement ratio. 2. Workability, mix design, storage, batching, mixing, placement, compaction, finishing and curing of concrete. 3. Quality control of concrete, hot weather and cold weather concreting repair, and maintenance of concrete structures. |
| RCC Design | 1. RCC beams-flexural strength, shear strength, bond strength, design of singly reinforced and double reinforced beams, cantilever beams. 2. T-beams, lintels.One-way and two-way slabs, isolated footings. 3. Reinforced brick works, columns, staircases, retaining walls, water tanks (RCC design questions may be based on both Limit State and Working Stress methods). |
| Steel Design | 1. Steel design and construction of steel columns. 2. Beams roof trusses plate girders. |
Other Important SSC Links
| SSC Previous Year Papers Download Free PDF Files | CLICK HERE |
| SSC Study Material Download Free PDF Files | CLICK HERE |
| SSC Syllabus PDF | CLICK HERE |
| Other Exam Material | CLICK HERE |
